Full of Stitches

Tuesday, December 20, 2022

Bridging the Gore

 Since my bra sewing adventure began, my fit models have changed shape. I started this not long after finishing breastfeeding my youngest baby, who is now school-aged. The internal factories have shut down, and downsized. In my last post, I expressed how my initial thoughts in bra sizing were being proven wrong. And, now I have some other helpful fit tips to use.

I have been sewing the Lansdowne bra because the shape is closer to anything that fits me from the rack. Last night, I printed off the Devonshire bridge and compared it to the Lansdowne bridge.



Turns out, this is why they say this bra is supposed to produce cleavage, the center gore is trimmed to a narrower width. Next, I cut a copy of the Devonshire bridge without any seam allowances from poster board.



And, then I chopped it in half. I took that and trimmed a bit off each side until I could fit the bridge against my chest.




The photo shows just how narrow the gap is… only about 1/4 to 3/8 of an inch (6-9 mm). So, if I directly compare that to the Lansdowne… It will show that the Lansdowne bridge is wider than what I need normally.


Also, I think that the pulling together of the bridge makes it taller, and rotates the cups… Will that cause more issues if I make the bra with a bridge that fits me? 


Labels: , , , , , , ,

Friday, February 19, 2021

Comparing Plunge Patterns

 I realized that the Lansdowne by Orange Lingerie is at least a plunge style bra, if not a push-up, similar to the Push-up by Merckwaerdigh. I went ahead and purchased it this week and sewed a first go of it along with a Push-up. I moved up one size in the Push-up, and made the size with the closest sized lower cup piece from the Lansdowne pattern: 85B vs. 34B. (Note: I could/should have made the 36A, so that I have room to shorten the band because my ribcage size is an odd number in inches, between the 34 and 36.)

Comparison photo: I sewed the band on upside down! Other than that, you can see that the shape of the Lansdowne (top, in picture) follows the natural curve, and looks more like a regular day bra that is just meant to smooth and hold. The Push-up, on the other hand, compresses the outer/lower breast, causing it to be pushed to the middle. I’ve put the same size wire in the left (right in picture) cup of each bra, leaving the right cup (left in pic) free to show the difference the pattern lines make, and that the wire supports. See how flat the lower cup is on the Push-up? That’s what I need to get the girls in front of me.

I had made the Push-up in the suggested size the first time, the XO bra for Valentines. This time, I went up a size. This pattern has a set band that gets adjusted to size for the band to fit, and the cups are all B cups that use “sister sizing” to differentiate them. (Lying sizes, if I go online to a famous company, my sister sizes are 34D and 36B!)

The wire I had used the first time I sewed Push-up doesn’t really fit me: it’s a rocker style, but it was short enough to fit in the underwire channel. This time, I left the channel ends open and tried the wire that fits me best. The wires stick out both ends.

For the Lansdowne, I used the exact same fabrics. I think if I had stretch lace, it may have nearly fit me. I do think I need to go up a size, though.

I think I may not be measuring myself right, so I turned to my dear hubs. He measured me as best he could, at all the funny angles the best bra calculator shows. I told him to measure, write and just give me the numbers after and he obliged, shooing my prying eyes. His measurements are different than mine.

Upper bust: 36”

Full bust 39” average of ways to measure

Band/ribcage: 31” fully exhaled

BCD: Right:3”, Left: 3.25” (which place me at 34B, and 36B, respectively)

Well, he does get different measurements than I do. The calculator suggests 34DD, UK or US sizes.

Neither bra that I made today fit me. and that’s okay. I’ll go another size up. I’ll try them all until I get a fitting band and cup, or close to it. 

Labels: , , , , , ,

Monday, September 30, 2019

Standards

I was feeling frustrated about bra shopping. There’s only so many you can try on. I’ve found that I can get by with certain bras, like Demi style, or those with a low center front, but they don’t fit. In the last year, I’ve dropped forty pounds. So, now I have to start over in my bra making. Starting with measurements.

Underbust:
-breathing out, as small as I can go is now 28.5”, 72.5 cm
-inhaled, as big as I can fill my lungs: 32”, 81.3 cm

Overbust:
-taken above breast, high against armpits, this goes around my  pectoral muscles and scapula: 34.5 to 35”, 89 cm

Bust:
-brafree as no bra fits and I only own padded ones... 37”, 94 cm

Notes about shape: small bust, fit(ish) shape, fullness in lower bust, short bust!, wide tissue

Wire size:
40 Carmen from Emerald Erin or UW920-40 from Sew Sassy (38 still has a gap underneath, 42 is too big). Most wires are too rounded underneath for me.

Pattern...
I’ve picked up several patterns to try. Sadly, they all fall prey to the normal standard of bust size. Mine are not skinny, tall, or full. So, the main Demi-bra available for sewists to use is Boylston. We will start there.

Boylston directions are to exhale fully, add 4 or 5” to the underbust. 28” and 4 is 32, or round up to 29” and 5” is 34. Measure fullest part of bust (“supportive bra” yadda yadda) and high bust, difference of 2” gives us a B cup. Therefore, I should make a 34B bra... let’s just call it cups don’t fit, but! it gives us a starting point.

Let’s look at that wire, though. I have to go to the website because the pattern does not include wire sizes!? A size 40 (a wire is the size B of said band size, unless otherwise stated) wire fits sizes: 30G, 32DDD, 34DD, 36D, 38C, 40B, and 42A. I’m going with the 34 band size, partly because there is no 32DDD in this pattern, so I’ll print out the 34DD band.

So, now I have a big cupped band, but a little cup size. I need to add to the edges of my cup to make it fit the wire length. What if we add evenly on the edges along the wire line? What’s the simplest way? I’m using the window as a lightbox, overlapping the smaller cup on the larger cup to trace the edges out, then smooth the line...





Inside lower cup, outside lower cup and upper cup all need the increases.
I’m taking photos over a very thin top. The cups are made from cup stabilizer tulle (Marquisette), and the wire is attached with double food bias tape.




Not bad... but, adding those wedges around the edges has put a smidge too much room into the cup. The wrinkles along the center show that I’m not quite filling that part right. We’ll straighten out the curve a bit on the lower cup pieces.






Interesting. This is a better fit than I’ve ever had. Still tight , somehow, but can’t quite tell what to fix next. Let’s try it in a bra!



The dreaded quad boob? I took the photo from this angle to show it. With the elastics attached, I can see that I need to give the upper cup a smidge more  room.  The right side isn’t nearly as bad...

Ah, I know, the upper cup lost its curve when the extra space was added to the sides.  Perhaps, I should use a larger size pattern piece for the upper cup?

I cut out the cups and remade one with the 34C cup widened to fit the cradle.
.


I think it fits better!


Let’s sew a Boylston.


Lefty fits now! I think I could reduce the curve along the wire some more. Righty is my smaller side and the cup is looser. I think the 34B version fit the right, so next time I will have to make the cups to fit each side. The straps attach at an awkward angle and also  need adjusting. I don’t have a photo, but the straps are way too wide set in the back as well. I suppose if I had a low square neckline, then  this would work. I’ve ordered more wires because the Sew Sassy ones fit this and I only had the one pair.

Labels: , , ,